Cisco QDD-400G-LR4-S Compatible 400GBASE-LR4 QSFP-DD Transceiver

Cisco compatible QDD-400G-LR4-S - Key Features
- Compatibility: Cisco
- Media Type: Single-Mode Fiber (SMF)
- Connector: Double LC/UPC
- Fiber Count: Duplex
- Maximum Distance: 10 km
- Average Link Budget: 7.1 dB
- Tx Wavelength: CWDM 4 Ch
- Supported Data Rate: 425 Gbps
- DDM/DOM: Supported
- Forward Error Correction (FEC): Host FEC Supported
- Temperature Range: Standard 0°-70°C
Cisco QDD-400G-LR4-S Price
Cisco compatible QDD-400G-LR4-S Specifications
Form Factor | QSFP-DD |
Modulation | PAM4 (Pulse Amplitude Modulation 4-level) |
Media Type | Single-Mode Fiber (SMF) |
Connector | Double LC/UPC |
Fiber Count | Duplex |
Maximum Distance | 10 km |
Average Link Budget | 7.1 dB |
TX Wavelength | 4-channel CWDM (1271/1291/1311/1331 nm) |
RX Wavelength | 4-channel CWDM (1271/1291/1311/1331 nm) |
Supported Data Rate | 425 Gbps |
Supported Ethernet Applications | 400G Ethernet (425 Gbps) |
DDM/DOM | Supported |
Forward Error Correction (FEC) | Host FEC Supported |
CDR (Clock and Data Recovery) chip | Supported |
Transmitter Type | EML Laser |
Tx Wave Bandwidth | 73 nm (1264.50–1337.50 nm) |
Average Launch Power (Min) Each Lane | -2.8 dBm |
Average Launch Power (Max) Each Lane | 4 dBm |
Extinction Ratio (Min) | 3.5 dB |
Receiver Type | PIN photodiode |
RX Wave Bandwidth | 73 nm (1264.50–1337.50 nm) |
Average Receiver Sensitivity (Min) Each Lane | -9.1 dBm |
Average Receiver Sensitivity (Max) Each Lane | 4 dBm |
Receiver Overload | 4.5 dBm |
Temperature Range | Standard 0°-70°C |
Storage Temperature | -40° to 85°C |
Relative Humidity | 5 to 85% |
Power Consumption (Max) | 9 W |
Power | +3.3V single power supply |
Compliance | CE;RoHS;Class 1 FDA and IEC60825-1 Laser Safety Compliant;100G Lambda MSA;400GBASE-LR4;IEEE 802.3bs;CMIS V4.0;QSFP-DD MSA |
Cisco compatible QDD-400G-LR4-S Datasheet
v4Complete technical specifications and product details
Cisco compatible QDD-400G-LR4-S Description
EdgeOptic's QDD-400G-LR4-S compatible is a Cisco-coded version of the EdgeOptic 400G-QSFP-DD-11 multi-vendor 400GBASE-LR4 QSFP-DD transceiver. It carries the same optical parameters as the Cisco original and is built to the same QSFP-DD MSA mechanical and electrical envelope, so it drops into Cisco QSFP-DD ports as a direct replacement for the OEM module.
The module carries four-channel CWDM optics on 1271, 1291, 1311 and 1331 nm, each lane driven by an EML transmitter and recovered on a PIN photodiode. Signaling is PAM4 at a 425 Gbps aggregate line rate, delivering 400G Ethernet over a duplex LC/UPC interface on standard single-mode fiber. The link supports a 7.1 dB average optical link budget, which covers reaches up to 10 km over OS2 fiber. Average launch power per lane runs from −2.8 dBm to +4 dBm, and receiver sensitivity is rated at −9.1 dBm per lane. Distance is an indicative figure derived from the average link budget and typical fiber attenuation, so verify the loss on the installed span during commissioning.
The 400GbE electrical and rate envelope is defined by IEEE 802.3bs, while the LR4 optical interface follows the 100G Lambda MSA 400G-LR4-10 specification. The host system supplies RS(544,514) KP4 forward error correction, and the module includes clock and data recovery on both the host and line sides. Digital diagnostic monitoring reports temperature, supply voltage, laser bias, transmit power and receive power per lane, and the module is managed over CMIS V4.0. It operates across a 0 to 70 degrees C case temperature range and draws up to 9 W. The 400G-QSFP-DD-11 platform is a 400GbE-only module: it does not carry Fibre Channel, OTN or SONET traffic.
EdgeOptic codes this compatible with Cisco-recognized EEPROM, so it is accepted on Cisco platforms with QSFP-DD ports without the service unsupported-transceiver command. The module is CE and RoHS certified, rated Class 1 laser per IEC 60825-1, and compliant with the QSFP-DD MSA. It suits internet service provider aggregation and backbone links, mobile operator core networks and data center core interconnect.
Backed by 15+ years of EdgeOptic compatibility engineering across vendor optical platforms, this module is made to order on a 2-week lead time and ships with a lifetime warranty. For coding queries or platform-specific deployment questions, contact our sales team.
Frequently Asked Questions
Does the EdgeOptic QDD-400G-LR4-S compatible require the Cisco service unsupported-transceiver command?
No. EdgeOptic codes this compatible with Cisco-recognized EEPROM, so Cisco platforms with QSFP-DD ports accept the module as a standard transceiver. The service unsupported-transceiver command is not needed, and the GBIC-invalid error state does not appear.
Is the QDD-400G-LR4-S the same optic as the QDD-400G-LR4-S=?
QDD-400G-LR4-S= is the Cisco spare-part ordering code, using the standard '=' suffix convention; it refers to the same module as QDD-400G-LR4-S, ordered through the spares channel. The EdgeOptic compatible covers this module. If your procurement system lists a specific Cisco code, confirm it with Cisco ordering before placing an order.